Skip to content
Alpha Devraj — Energy Storage Systems

Fundamentals

How can textile and spinning mills in India use battery storage to cut power costs?

A spinning mill runs a near-flat load 24 hours a day, so it pays peak-hour surcharges on a large share of its units. A battery charges in cheaper hours and discharges in the peak windows, cutting the surcharge, replacing costly diesel during grid restrictions, and storing captive solar instead of banking it with the discom.

Published 7 November 2026 · Last updated 7 November 2026 · 6 min read · By Alpha Devraj ESS Research Desk

On this page

A spinning mill is one of the most electricity-hungry businesses in Indian manufacturing, and one of the least flexible about when it uses that electricity. Ring frames run three shifts. Humidification runs whenever the machines do. Stopping the line for two hours because power is expensive is rarely an option.

That combination — high, steady, round-the-clock load on a tariff that charges more at certain hours — is exactly where a battery energy storage system (BESS) earns its keep.

Why power matters so much in a mill

Energy is commonly cited as 15–20% of a textile mill’s production cost, second only to raw material. For a mill competing on yarn margins measured in rupees per kilogram, a few percent off the power bill is a meaningful number.

Where that power goes is also well understood. In one worked example for 20 tex combed ring yarn, the breakdown was:

LoadShare of mill electricity
Production machines71.5%
Air conditioning and humidification17.5%
Compressors7.7%
Lighting3.2%

Within the machines, ring spinning alone used 55.5% of the machine energy and carding 18.2%. The same example works out to about 3.32 kWh per kilogram of yarn.

The practical point is that almost all of this is process load. It does not fall away at 6 pm when the tariff goes up.

The tariff problem: a flat load on a peaked tariff

Take Tamil Nadu, home to a large share of India’s spinning capacity, as a worked example. Under TNERC Tariff Order No. 6 of 2025, effective 1 July 2025, an HT industrial consumer (category HT I) pays:

  • ₹7.50 per unit as the base energy charge
  • A 25% surcharge on energy in two peak windows: 6–10 am and 6–10 pm
  • A 5% rebate in the night window, 10 pm–5 am
  • ₹608 per kVA per month as the demand charge
Energy charge through the day, ₹ per unit (HT I)₹7.13₹9.38₹7.50₹9.38₹7.130:005610182224battery chargesbattery dischargesrecharge (or solar)battery dischargesPeak = ₹7.50 + 25% surcharge. Night = ₹7.50 − 5% rebate. Demand charge (₹608/kVA/month) is billed separately.
Tamil Nadu HT industrial energy charge across a day under TNERC Tariff Order No. 6 of 2025. A spinning mill running flat out pays the higher rate for eight of every 24 hours.

For an office building, the peak windows catch a slice of the day’s use. For a spinning mill they catch eight of every 24 hours of a flat load — about a third of all units consumed.

Here is what that means in rupees. A mill drawing a steady 1 MW uses 8,000 units a day in the peak windows. The 25% surcharge on those units is about ₹1.88 each, or roughly ₹15,000 a day — around ₹4.5 lakh a month — before anything else on the bill. That surcharge is the pool of money a battery goes after.

This is the time-of-day (ToD) tariff mechanism, and mills are close to the worst-case customer for it.

Where a battery saves money in a mill

1. Shifting units out of the peak windows. The battery charges when power is cheap and discharges during the peaks. On the Tamil Nadu numbers, a unit charged at night (₹7.13) and used in the morning peak (₹9.38) saves about ₹2.25 before losses; a unit charged in the daytime normal window (₹7.50) and used in the evening peak saves about ₹1.88. Some energy is lost in every cycle, so the real saving per unit is somewhat lower — see round-trip efficiency and degradation.

Two peak windows a day also means the battery can do two useful cycles a day, which is good for payback and something to plan for in the warranty.

2. Replacing diesel during grid restrictions. In September 2026 the Open-end Spinning Mills Association asked the government to ensure 24-hour uninterrupted grid power for HT industrial consumers, after units were reportedly pushed onto diesel generators during evening peak hours. Diesel was put at around ₹30 per unit — several times the grid tariff. Every peak-hour unit a battery covers instead of a generator is a large saving, which is why the comparison in BESS versus diesel genset tends to be stark for continuous-process plants.

3. Getting more out of captive solar and wind. Tamil Nadu’s textile industry owns roughly 3,000 MW of wind and 1,500 MW of solar, much of it under group captive arrangements. Generation that does not line up with consumption has to be banked with the discom or wheeled — and mills have reported banking charges, transmission fees and losses eating into the benefit. A battery on site lets midday rooftop solar carry the evening peak instead. That is the solar plus storage configuration, and the open-access side is covered in captive versus open access solar for factories.

4. Smoother power for sensitive machinery. Mills have flagged that frequent switching between grid and generator risks equipment damage and production delays. A battery that picks up the load instantly removes that switching shock.

5. Some demand charge relief. With a ₹608/kVA demand charge, any spike — a restart after an outage, compressors and humidification plant coming on together — is expensive. A mill’s load is flat, so this is a smaller lever than for a commercial building, but it is not zero. The mechanism is in demand charges explained, and the battery function is peak shaving.

Sizing honestly for a mill

The trap is sizing a battery to “cover the peak” at full mill load. A 5 MW mill wanting to ride through a full four-hour window needs around 20 MWh usable — a utility-scale system. That can still make sense, but most mills will start smaller:

  • Cover the costliest window first. The morning peak has the largest spread over the cheapest night rate.
  • Cover the loads you choose. Humidification and auxiliary loads can be put on the battery while the main process stays on grid.
  • Size against your interval meter data, not the sanctioned load. Fifteen-minute data from the last year shows the real peak-window consumption.
  • Model the two-cycle day. Recharge time between the morning and evening peaks is eight hours, which is plenty, but only if the charging power is sized for it.

The step-by-step method is in how to size a BESS for your site.

What this means for you

  • If you run a spinning or weaving mill: pull the last 12 months of HT bills and find the peak-hour units and the surcharge line. For a flat-load mill, that number — not the demand charge — usually decides whether storage pays.
  • If you face peak-hour restrictions: price your diesel per unit honestly, including fuel, maintenance and downtime. At around ₹30 a unit, a battery covering even part of the restricted window can pay back quickly.
  • If you own captive solar or wind: ask what your banking and wheeling charges cost you each year. Storing on site may beat banking.
  • If you want numbers for your own mill: run your tariff and load through our BESS savings calculator, or browse our products and talk to our team about a sized proposal.

Tariff orders, ToD windows, surcharges and banking rules are set by state regulators and change by notification. The Tamil Nadu figures here reflect TNERC Tariff Order No. 6 of 2025 as reported in November 2026; verify the current terms for your state and category before making an investment decision.

Frequently asked questions

Our load is flat all day. Is there anything to shave?

Not much in the demand-charge sense, but a lot in the time-of-day sense. A flat load pays the peak surcharge on every unit it uses in the peak windows. Moving those units into cheaper hours is the main saving, and it does not need a spiky load to work.

Can a battery run the whole mill through a peak window?

It can, but it does not have to. Many mills size the battery to cover part of the peak, or the most expensive window, and accept the surcharge on the rest. Covering a full four-hour peak at full load needs a battery of roughly four hours at your average demand, which is a large system for a big mill.

We already own wind and solar. Does storage still help?

Often more, not less. Captive generation that does not match your consumption hour by hour has to be banked or wheeled, with fees and losses. A battery on site lets you hold midday solar for the evening peak instead of handing it to the grid and buying it back.

Does it help with power quality?

Yes. Spinning machinery dislikes interruptions and repeated switching between grid and generator. A battery that takes over instantly smooths those transitions, which mills have flagged as a source of equipment damage and lost production.

Let's talk storage

Want these numbers for your site?

Send a bill or a load profile — we model it and tell you straight.